1. Social||Forum, leaderboard, users
  3. Forum
  5. International Section
  7. Do it Yourself
  9. DIY autopilot GoPro Drone - RC Multicopter Buldlog
× Do it Yourself projects - everything you made / modified / invented by yourself.

DIY autopilot GoPro Drone - RC Multicopter Buldlog

More
10 years 8 months ago - 10 years 8 months ago #14 by Stuyo
Stuyo replied the topic: DIY autopilot GoPro Drone - RC Multicopter Buldlog
Quanum Trifecta Frame assembly + Baby Beast motor mounting + Afro ESC mounting and testfit:

IMG_5981.JPG


IMG_5982.JPG


Resources:
1. Baby Beast outrunner - Multistar V2 2206-2150KV Motor The "Baby Beast" (V2)
2. Afro ESC 12A - Afro ESC 12Amp Ultra Lite Multi-rotor Motor Speed Controller (SimonK Firmware) Version 3
3. MG Servo - Turnigy TGY-9018MG Metal Gear Servo 2.5kg/13g/0.10
Attachments:
Last Edit: 10 years 8 months ago by Stuyo.

Please Log in to join the conversation.

More
10 years 8 months ago - 10 years 8 months ago #15 by Stuyo
Stuyo replied the topic: DIY autopilot GoPro Drone - RC Multicopter Buldlog
HKPilot Micro PDB - Power distribution module, cable routing:
Micro HKPilot Mega PDB, BEC and Volt/AMP Sensor 30.5mm Mounting


IMG_5983.JPG


IMG_5991.JPG


IMG_5995.JPG
Attachments:
Last Edit: 10 years 8 months ago by Stuyo.

Please Log in to join the conversation.

More
10 years 8 months ago - 10 years 8 months ago #16 by Stuyo
Stuyo replied the topic: DIY autopilot GoPro Drone - RC Multicopter Buldlog
HKPilot Mega Micro controller Arducopter board put in a modified CC3D plastic HK case - cut wit saw, sanded and cutouts with exacto knife:


IMG_5998.JPG


IMG_5996.JPG


IMG_5997.JPG


Resources:
1. HKPilot Mega Micro APM - Micro HKPilot Mega Micro Sized Flight Controller and Autopilot with Leads 2.7.2 (APM)
2. CC3D plastic case - Openpilot CC3D Flight Controller Protective Case
Attachments:
Last Edit: 10 years 8 months ago by Stuyo.

Please Log in to join the conversation.

More
10 years 8 months ago - 10 years 8 months ago #17 by Stuyo
Stuyo replied the topic: DIY autopilot GoPro Drone - RC Multicopter Buldlog
The GPS module is not direct so i had to cut a piece of 2mm soft plastic.

First, cut 25mm square hole for the GPS body, then cut outside and drill holes for mounting:

IMG_6003.JPG


IMG_6004.JPG


Resources:
Micro HKPilot GPS And Compass u-Blox NEO-6 and HMC5883
Attachments:
Last Edit: 10 years 8 months ago by Stuyo.

Please Log in to join the conversation.

More
10 years 8 months ago - 10 years 8 months ago #18 by Stuyo
Stuyo replied the topic: DIY autopilot GoPro Drone - RC Multicopter Buldlog
The receiver - shortened antenna to save space (i don't need very long range):

IMG_6008.JPG
Attachments:
Last Edit: 10 years 8 months ago by Stuyo.

Please Log in to join the conversation.

More
10 years 8 months ago - 10 years 8 months ago #19 by Stuyo
Stuyo replied the topic: DIY autopilot GoPro Drone - RC Multicopter Buldlog
Controller installation, GPS, Telemetry and telemetry protection cover:

IMG_6012.JPG


IMG_6014.JPG


Resources:
Micro HKPilot Telemetry radio Set With Integrated PCB Antenna 433Mhz
Attachments:
Last Edit: 10 years 8 months ago by Stuyo.

Please Log in to join the conversation.

  1. Social||Forum, leaderboard, users
  3. Forum
  5. International Section
  7. Do it Yourself
  9. DIY autopilot GoPro Drone - RC Multicopter Buldlog
Time to create page: 0.529 seconds
Powered by Kunena Forum

Продава се - най нови

Нови маршрути